Read Featured Reviews From Actual Customers Read All Reviews
AT&T FirstNet on the Go
When emergencies strike, reliable cellular and internet access are critical for the success of response efforts. The PSU Commander offers reliable AT&T FirstNet connectivity across all channels using the sheer power of batteries. Set up a command center anywhere and run it with AT&T FirstNet Bands 12 and 14, fast WiFi, and gigabit Ethernet.
Enhance Mission-Critical Communication
Equipped with the most powerful AT&T FirstNet signal booster, the PSU Commander enhances Bands 12 and 14 by up to 100 dB for all nearby cellular devices, including the LTE router. That’s 30 dB more than other signal boosters. Emergency communication from police, fire, and medical personnel will significantly improve. Monitor performance with the Cel-Fi WAVE app.
The AT&T FirstNet ready router takes the boosted signal and delivers continuous internet connectivity. Offers up to 300 Mbps download and 150 Mbps upload. It also has built-in GPS and dual-SIM capabilities. Designed to work where other routers can’t, expect superior performance, especially when paired with the Cel-Fi GO Red.
Deploy Anywhere Disaster Strikes
Portable and battery-powered, the PSU Commander is the perfect companion for first responders and the public safety community. Including two batteries, keep all necessary equipment connected for up to 18 hrs. Alternate AC power available. Built-in power strip and USB ports allow for additional connections. Simple five minute tool-free installation.
*Battery charger sold separately.
Improve Public Safety
Set up the PSU Commander anywhere and get superior FirstNet connectivity for mission-critical communication. With everything needed inside the case, the PSU Commander can be up and running in minutes. Lid must remain open during operation for optimal performance. With reliable cell reception and internet access, public safety response time and decision making improve, making the world a better place.
The PSU Commander by Bolton Technical provides AT&T FirstNet connectivity on the go. It’s equipped with a Cel-Fi GO Red Signal Booster and a FirstNet ready LTE router. Anywhere cellular reception is lacking or congested, the PSU Commander offers superior FirstNet cell reception, fast WiFi, and gigabit Ethernet.
The Cel-Fi GO Red enhances AT&T’s FirstNet Bands 12 and 14 by up to 100 dB. Compared to other amplifiers, that’s up to 1000x more powerful. The Peplink UBR LTE router takes amplified FirstNet signal and delivers fast, reliable internet (up to 300 Mbps). All cellular and data-driven public safety equipment will receive enhanced priority service for continuous mission-critical uptime.
Everything needed for superior communication and internet access is included in the portable, heavy-duty case. With time being of the essence, the PSU Commander is quick and easy to set-up.
- Portable AT&T FirstNet signal booster and LTE CAT 6 router
- Priority connectivity
- Reliable cellular connectivity
- Boosts AT&T Band 12 and 14, up to 100 dB
- Fast WiFi and Ethernet connectivity, up to 300 Mbps
- Dual-SIM failover
- Easy to read voltage meter
- Easy to set up and use
- Built-in USB port and power strip
- Public Safety Personnel
- First Responders (Fire, Police, EMS)
- Temporary Command Centers
- Medical Service Stations
|Manufacturer||Pepwave - UBR Dual Cellular Router|
|Number of Ports||5x LAN or, 4x LAN + 1x WAN|
|Port Speeds||1 Gbps|
|Peek Data Speeds||DL 300 Mbps, UL 150 Mbps|
|Antennas||4x LTE Whip, 2x WiFi Whip, 1 GPS|
|Manufacturer||CEL-FI GO RED|
|Frequency Bands||12, 14|
|Gain||100 decibels (dB)|
|Input Power||9.6 - 15.6 V|
|Dimensions||3.8 X 1.75 x 10.75 inches|
|WHATS IN THE BOX|
|1 Ft. Jumper Cable||N-Connectors|
|Right Angle Connector||N-Connectors|
|50 Ft. LMR 400 Cable||N-Connectors|
|Panel Antenna (Indoor)||50 Ohm|
|Yagi Antenna (Outdoor)||50 Ohm|
|7 Ft. Extendable Tripod||Quick Connect|
|Gross Weight||45 lbs|
|Net Weight||50 lbs|
|Dimensions||24" X 15" X 18"|
|Router FCC ID||XMR201807EP06A|
|Booster FCC ID||0019823665|
This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by FCC or a licensed wireless service provider.
- Assemble tripod and add weight if needed.
- Mount Yagi antenna.
- Point Yagi antenna at your closest cell tower. Use the Cel-Fi WAVE app to easily locate the tower.
- Connect coaxial cable to the Yagi antenna and signal booster.
- Make sure Yagi and panel antennas are facing opposite directions and that there is at least 30 ft of separation between them.
- Lift router's LTE and WiFi antennas
- Turn on PSU Commander
- Enjoy enhanced WiFi and cellular signals
For assistance, please call us at 1-800-470-6777.
Frequently Asked Questions
One includes a Cel-Fi GO Red signal booster and cellular router, while the other just includes the signal booster.
The PSU Commander works with AT&T FirstNet bands 12 and 14 only.
AT&T FirstNet only.
Once on, cellular devices using black AT&T FirstNet SIM cards automatically pick up the amplified signal from the Cel-Fi GO Red. To connect to the router, refer to the instructions included.
Yes, even if weak. Both the amplifier and router use cellular signals to provide reliable connectivity. The booster picks up available signal, amplifies it, and delivers stronger cell reception for all nearby cellular enabled AT&T FirstNet devices to use. That includes the router.
The only monthly fee associated with the PSU is the data plan needed to keep the Bolton Blazer online.
If closed, the cellular and WiFi signals can’t propagate efficiently. In addition, there won’t be enough separation between the panel and whip antennas. This will cause significant oscillation.
Yes. You can use the Cel-Fi WAVE app to simplify the set-up process and monitor the Cel-Fi Go Red’s performance.
The PSU Commander comes standard with a Yagi antenna. Under best conditions, it can reach cell towers located up to 5 miles away. For extremely weak signal environments, you can upgrade the donor antenna to an LPDA. They are more powerful and can reach cell towers located up to 7 miles away under best conditions. Though, the LPDA will not fit in the case.
Because of signal propagation, the PSU Commander will perform best in enclosed areas. However, it can also be used outdoors.